R-net trip codes

Trouble:

When a fault is detected by the device, an R-net trip code will be generated. The trip code will be shown on the joystick (if it is present and equipped with a graphic display). The trip code will also be logged in the R-net system and can be investigated using the R-net PC Programmer.

If you want to learn more about trip codes, see the Curtiss-Wright manual | SK77981-14 R-net Technical Manual.


R-net trip code	Reason	Required action
9600	Uart overflow	Update firmware or replace PCB.
9601	Uart underflow	Update firmware or replace PCB.
9602	Packet transmission exceeded maximum number of retries	Update firmware or replace PCB.
9603	TX handle overflow	Update firmware or replace PCB.
9604	RX handle overflow	Update firmware or replace PCB.
9605	Invalid sequence number	Update firmware or replace PCB.
9606	Ack number does not match	Update firmware or replace PCB.
9607	Invalid packet descriptor	Update firmware or replace PCB.
9608	Incorrect R-net version	Update firmware or replace PCB.
9609	Chip tripped	Update firmware or replace PCB.
960A	Invalid response when accessing a file	Update firmware or replace PCB.
9620	CPU error	Update firmware or replace PCB.
9621	Code error	Update firmware or replace PCB.
9640	One or more test flags not set	Redo tests and/or replace PCB.
9641	Software watchdog	Update firmware or replace PCB.
9642	There was a problem during the preparation of the R-net system	Check R-net fault on joystick display or in the R-net PC programmer. Check R-net configuration.
9643	Left sensor is faulty	Replace sensor board and calibrate.
9644	Right sensor is faulty	Replace sensor board and calibrate.
9645	Left throttle is faulty	Replace throttle and calibrate.
9646	Right throttle if faulty	Replace throttle and calibrate.
9647	There is an R-net trip code	Check R-net fault on joystick display or in the R-net PC programmer.
9648	Factory test failed	A fault occurred during factory testing.
9649	Field test failed (calibration)	A fault occurred during field testing (calibration).
9800	API_MSG_SEND_TO_FREQUENTLY	Update firmware or replace PCB, check R-net configuration.
9801	API_MSG_DATA_OUT_OF_RANGE	Update firmware or replace PCB, check R-net configuration.
9802	API_MSG_ID_UNKNOWN	Update firmware or replace PCB, check R-net configuration.
9803	API_MSG_DATA_INCORRECT_AMOUNT	Update firmware or replace PCB, check R-net configuration.
9804	API_MSG_TOO_SHORT	Update firmware or replace PCB, check R-net configuration.
9805	API_MSG_TOO_LONG	Update firmware or replace PCB, check R-net configuration.
9806	API_MSG_NOT_ENABLED	Update firmware or replace PCB, check R-net configuration.
9807	API_RESPONDED_OUT_OF_TIME	Update firmware or replace PCB, check R-net configuration.
9808	API_MSG_REQUIEREMENT_WRONG	Update firmware or replace PCB, check R-net configuration.
9809	API_MSG_INVALID_IN_CURRENT_STATE	Update firmware or replace PCB, check R-net configuration.
9810	DATA_PACKET_WITH_INVALID_SEQ_NR	Update firmware or replace PCB, check R-net configuration.
9811	ACK_PACKET_WITH_INVALID_SEQ_NR	Update firmware or replace PCB, check R-net configuration.
9812	INVALID_HEADER	Update firmware or replace PCB, check R-net configuration.
9813	PACKET_TIMEOUT	Update firmware or replace PCB, check R-net configuration.
9814	CHIP_INT_ERR0	Update firmware or replace PCB, check R-net configuration.
9815	CHIP_INT_ERR1	Update firmware or replace PCB, check R-net configuration.
9816	HOST_RESTART_AFTER_CORRECT_INIT	Update firmware or replace PCB, check R-net configuration.
9817	HOST_INCOMPATIBLE_SERIAL_PROTOCOL_VERSION	Update firmware or replace PCB, check R-net configuration.
9820	CHIPSET_INTERNAL_QUEUE_OVERFLOW	Update firmware or replace PCB, check R-net configuration.
9821	CHIPSET_HEARTBEAT	Update firmware or replace PCB, check R-net configuration.